LPV-18E
Share:
Features:
‧180-264VAC input only
‧Fully encapsulated with IP67 level (Note.5)
‧Protections: Short circuit / Overload / Over voltage / Over temperature
‧Cooling by free air convection
‧Class 2 unit ,no FG
‧Pass LPS
‧100% full load burn-in test
‧Suitable for LED lighting and moving sign applications
‧High reliability / Low cost
‧3 years warranty
NOTE:
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 ℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
7. Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minute.
8. The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit.
‧180-264VAC input only
‧Fully encapsulated with IP67 level (Note.5)
‧Protections: Short circuit / Overload / Over voltage / Over temperature
‧Cooling by free air convection
‧Class 2 unit ,no FG
‧Pass LPS
‧100% full load burn-in test
‧Suitable for LED lighting and moving sign applications
‧High reliability / Low cost
‧3 years warranty
| Model | LPV-18E-12 | LPV-18E-24 | LPV-18E-36 | |||||
|
Output |
DC voltage | 12V | 24V | 36V | ||||
| Rated current | 1.5A | 0.75A | 0.5A | |||||
| Current range | 0~1.5A | 0~0.75A | 0~0.5A | |||||
| Rated power | 18W | 18W | 18W | |||||
| Ripple&noise (max.) | 120mVp-p | 150mVp-p | 200mVp-p | |||||
| Voltage tolerance | ±3.0% | |||||||
| Line regulation | ±1.0% | |||||||
| Load regulation | ±2.0% | |||||||
| Setup,rise time | 1500ms,30ms / 230VAC | |||||||
| Hold up time | 50ms/230VAC at full load | |||||||
| Input | Voltage range | 180 ~ 264VAC , 254 ~ 370VDC | ||||||
| Frequency range | 47 ~ 63Hz | |||||||
| Efficiency | 77% | 82% | 83% | |||||
| AC current | 0.3A/230VAC | |||||||
| Inrush current | Cold start 50A(twidth=155μs measured at 50% Ipeak) at 230VAC | |||||||
| Leakage current | <0.25mA/240VAC | |||||||
|
Protection |
Overload | Above 105% rated output power | ||||||
| Protection type：hiccup mode，auto-recovery after fault condition is removed | ||||||||
| Over voltage | 13.8~ 16.2V | 27.6~ 32.4V | 41.4~ 48.6V | |||||
| Protection type : Shut off o/p voltage, clamping by zener diode | ||||||||
| Over temperature |
Hiccup mode, recovers automatically after temperature goes down |
|||||||
| Environment | Working humidity | 20%~90%RH non-condensing | ||||||
| Storage temp,humidity | -40℃~+80℃,10%~95%RH non-condensing | |||||||
| Temp. coefficient | ±0.03%/℃ (0 ~ 50℃) | |||||||
| Vibration | 10~500HZ,2G 10min/1cycle,period for 60min, X.Y.Z each axes | |||||||
|
Safety&EMC |
Safety standard | TUV EN60950-1, TUV EN61347-1,EN61347-2-13,IP67 approved; design refer to UL1310 Class 2,CAN/CSA No. 223-M91 | ||||||
| Withstand voltage | I/P-O/P:3KVAC | |||||||
| Isolation resistance | I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH | |||||||
| EMC emission | Compliance to EN55022 Class B,EN61000-3-2 Class A, EN61000-3-3 | |||||||
| EMC immunity | Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A | |||||||
| Others | MTBF | 1100K hrs min. MIL-HDBK-217F (25℃) | ||||||
| Dimension | 140*30*22(L*W*H) | |||||||
| Packing | 0.175Kg; 70pcs/13.3Kgs/0.71CUFT | |||||||
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 ℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
7. Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minute.
8. The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit.
Inquiry - LPV-18E
view more about
LPV Series Power Supply
